Rainbow Engineering Services

Load-Bearing Wall Removal Gold Coast | Rainbow Engineering
Load-bearing wall assessment, removal & beam design · Gold Coast

Load-bearing wall removal on the Gold Coast

Taking out a load-bearing wall for an open-plan renovation? An RPEQ structural engineer inspects the wall, confirms whether it’s load-bearing, and designs the steel or timber beam, posts and footings to replace it — then certifies the work so your builder can remove the wall safely and legally.

  • Is it load-bearing? Checked on site by an engineer
  • Beam, post and footing design your builder can install
  • Form 15 for approval, Form 12 once it’s installed
30+
Years of experience
RPEQ
Registered engineers
AIB
President’s Award — Chief Engineer

Builder waiting on engineering? Call 0499 887 867

Get a wall removal quote

Tell us about the wall

An RPEQ engineer reviews every enquiry and comes back with the next step and the fee. No obligation.


Photos of the wall and a rough floor plan help us quote quickly.

Certified — National Engineering Register (NER)
Board of Professional Engineers Queensland (BPEQ)
RPEQ Form 15 & Form 12
Wall removal projects

Structural wall removal for Gold Coast homes.

Pick the closest match to start your quote.

How to tell if a wall is load-bearing

Load-bearing or non-load-bearing?

A load-bearing wall carries weight from above — the roof, ceiling or upper floor — down to the footings. These are clues, not answers: only an inspection of the framing confirms it, and getting it wrong can mean sagging ceilings, cracked walls or worse.

Likely load-bearing
  • External walls
  • Walls directly under an upper-storey wall
  • Walls running perpendicular to the ceiling joists, supporting them
  • Walls supporting roof struts or a staircase
  • Internal brick or block walls in older homes
Check carefully
  • Walls near the centre of the house
  • Walls with a beam, bearer or thicker footing below
  • Concrete or masonry walls in units
  • Walls marked as load-bearing on the original floor plan
Often not — but confirm
  • Short partition walls
  • Walls running parallel to the ceiling joists
  • Wardrobe and linen cupboard walls
  • Walls under roof trusses that span wall to wall

Even a non-load-bearing wall can provide bracing for trusses, or hide services. Removing a non-load-bearing wall is usually simpler — but confirm first.

Replacing a load-bearing wall with a beam

What supports the load once the wall comes out.

Removing a load-bearing wall means transferring its load to a beam, then down through posts to footings. We design every part of that path.

Steel beam

Longer spans, heavier loads

A steel beam suits long openings and walls carrying an upper floor or brickwork. Usually the choice when you want the widest open-plan space.

Timber or LVL beam

Shorter spans, lighter loads

Engineered timber beams suit many single-storey homes and are easy for builders to install alongside existing framing.

Flush or dropped beam

Hidden in the ceiling, or below it

A flush beam sits up with the ceiling joists for a clean ceiling line; a dropped beam sits below. Which works depends on the span, load and roof framing.

Posts, columns & footings

Getting the load to the ground

Beam ends create point loads, so posts or columns often need new or bigger footings, especially on slab homes. Sometimes a column mid-span lets a smaller beam do the job.

Temporary supports: while the wall is removed and the beam installed, the structure above is propped on temporary supports. Our design includes notes so your builder can do this safely. Want a rough feel for beam sizes first? Try our beam load calculator.

Load-bearing wall removal cost

What affects the cost of removing a load-bearing wall.

Every wall is different, so there’s no fixed price. These are the things that move it.

Engineering (us)
  • Span of the opening
  • What the wall carries — roof only, or an upper floor
  • Single storey, two-storey or split-level
  • Assessment only, or full design with Form 15 and Form 12
Beam & installation (builder)
  • Steel or timber beam, and its size
  • Flush beam vs dropped beam
  • New posts, columns and footings
  • Temporary supports and access
Everything else
  • Brick or block walls vs timber-framed
  • Electrical, plumbing and services in the wall
  • Making good ceilings, floors and finishes
  • Approvals, and body corporate for units

We quote the engineering. Your builder quotes the beam installation and removal — and an engineered design lets them price it accurately instead of guessing.

What you receive

Everything to take the wall out properly.

01

Load-bearing wall inspection

An RPEQ engineer inspects the wall, roof space and subfloor to confirm what it carries.

02

Beam, post & footing design

Steel or timber beam sized for the load to Australian Standards, plus posts, connections, footings and temporary support notes.

03

Form 15

Design compliance certificate so your certifier can approve the work. About Form 15

04

Form 12 inspection

We inspect the beam and supports once installed and issue the Form 12. About Form 12

Part of a bigger renovation? We design the whole structure.

Structural design
How it works

From “can this wall go?” to certified.

Looking for load-bearing wall removal contractors? Your builder removes the wall and installs the beam; we provide the engineering they build from, and certify it.

1

Send photos and a plan

Photos of the wall, a rough floor plan and what you want to open up.

2

Site assessment

We confirm whether it’s load-bearing and what the wall is carrying.

3

Design and Form 15

Beam, posts, footings and temporary propping notes for your builder, with the Form 15 for approval.

4

Install and Form 12

Your builder installs it; we inspect and issue the Form 12 for your certifier.

Google Reviews

What Gold Coast renovators say.

FAQ

Load-bearing wall removal questions we get every week.

Clues include external walls, walls under an upper-storey wall, and walls running perpendicular to the ceiling joists that support them. Walls running parallel to the joists, or under trusses that span wall to wall, often aren’t. But the only reliable answer comes from inspecting the roof space, ceiling and subfloor framing, which is what a load-bearing wall inspection does.

Yes, in most homes. The wall’s load is transferred to a beam, which is supported on posts or columns down to footings. An engineer designs the beam, supports and footings, and your builder installs them with temporary supports in place while the wall is removed.

Removing or altering a load-bearing wall is structural building work, so it usually needs building approval from a certifier, supported by an engineer’s design and Form 15. In a unit, the wall may also be common property, so body corporate approval is usually needed too.

It depends on the span, what the wall carries, whether it’s timber-framed or brick, the beam type, new footings, services in the wall and making good afterwards. The engineering is one part of the cost; the builder’s beam installation and removal is the larger part. An engineered design lets your builder quote accurately.

Steel beams suit longer spans and heavier loads, such as walls carrying an upper floor. Engineered timber beams suit many shorter, single-storey spans. We size the beam for your wall and tell you which is practical.

Often, with a flush beam that sits up with the ceiling joists, depending on the span, the load and the roof framing. Otherwise a dropped beam sits below the ceiling. We’ll tell you whether a flush beam is practical.

Usually not for the structure itself, but it’s worth confirming the wall really is non-load-bearing first, and that it isn’t providing bracing. Services in the wall still need a licensed electrician or plumber.

Yes. Internal brick and block walls are often load-bearing and heavier to support, so the beam and footings need careful design, especially in two-storey homes.

Beam and wall design typically draws on standards such as AS 1684 for residential timber framing, AS 4100 for steel structures and AS 3700 for masonry, depending on the materials. We design and certify to the relevant standards for your home.

Get it assessed, especially if ceilings are sagging or cracks have appeared. We inspect what’s supporting the structure now, design any upgrades needed and provide the engineering for retrospective approval. Retrospective certification.

We’re the structural engineers. Your builder or contractor removes the wall and installs the beam; we inspect, design the beam and supports, and certify the work so it can be approved.

Areas we cover

Load-bearing wall removal across the Gold Coast.

Helensvale Hope Island Coomera Southport Surfers Paradise Broadbeach Benowa Robina Nerang Mudgeeraba Burleigh Heads Palm Beach Coolangatta

Our office is in Helensvale, on the northern Gold Coast.

Open it up safely

Get your load-bearing wall removal engineered.

Send photos of the wall and a rough plan. An RPEQ engineer will come back with the next step and the fee.

River Links Blvd E, Helensvale QLD 4212
Get a wall removal quote

Tell us about the wall

No obligation. Reviewed by an RPEQ engineer.


error: Content is protected !!
Call Us Now